Roofers

Roofers repair and install the roofs of buildings using a variety of materials, including shingles, asphalt, and metal.

Roofers typically do the following:

  • Inspect problem roofs to determine the best way to repair them
  • Measure roof to calculate the quantities of materials needed
  • Replace damaged or rotting joists or plywood
  • Install vapor barriers or layers of insulation
  • Install shingles, asphalt, metal, or other materials to make the roof watertight
  • Align roofing materials with edges of the roof
  • Cut roofing materials to fit angles formed by walls, vents, or intersecting roof surfaces
  • Cover exposed nail or screw heads with roofing cement or caulk to prevent leakage

Properly installed roofs keep water from leaking into buildings and damaging the interior, equipment, or furnishings.

There are two basic types of roofs, low-slope and steep-slope:

  • Low-slope: About two-thirds of all roofs are low-slope. Most commercial, industrial, and apartment buildings have low-slope roofs. Low-slope roofs rise 4 inches or less per horizontal foot and are installed in layers.

    For low-slope roofs, roofers typically use several layers of roofing materials or felt membranes stuck together with hot bitumen (a tar-like substance). They glaze the top layer to make a smooth surface or embed gravel in the hot bitumen to make a rough surface.

    An increasing number of low-slope roofs are covered with a single-ply membrane of waterproof rubber or thermoplastic compounds.
  • Steep-slope: Most of the remaining roofs are steep-slope. Most single-family houses have steep-slope roofs. Steep-slope roofs rise more than 4 inches per horizontal foot.

    For steep-slope roofs, roofers typically use asphalt shingles, which often cost less than other coverings. On steep-slope roofs, some roofers also install tile, solar shingles, fiberglass shingles, metal shingles, or shakes (rough wooden shingles).

    To apply shingles, roofers first lay, cut, and tack 3-foot strips of roofing over the entire roof. Then, starting from the bottom edge, they nail overlapping rows of shingles to the roof.

A small but increasing number of buildings now have “green” roofs that incorporate landscape roofing systems. A landscape roofing system typically begins with a single or multiple waterproof layers. After that layer is proven to be leak free, roofers put a root barrier over it, and, finally, layers of soil, in which vegetation is planted. Roofers must ensure that the roof is watertight and can endure the weight and water needs of the plants.


Painters, Construction and Maintenance

Painters apply paint, stain, and coatings to walls, buildings, bridges, and other structures.

Painters typically do the following:

  • Cover floors and furniture with drop-cloths and tarps to protect surfaces
  • Remove fixtures such as pictures, door knobs, or electric switch covers
  • Put up scaffolding and set up ladders
  • Fill holes and cracks with caulk, putty, plaster, or other compounds
  • Prepare surfaces by scraping, wire brushing, or sanding to a smooth finish
  • Calculate the area to be painted and the amount of paint needed
  • Apply primers or sealers so the paint will adhere
  • Choose and mix paints and stains to reach desired color and appearance
  • Apply paint or other finishes using hand brushes, rollers, or sprayers

Applying paint to interior walls makes surfaces attractive and vibrant. In addition, paints and other sealers protect exterior surfaces from erosion caused by exposure to the weather.

Because there are several ways to apply paint, workers must be able to choose the proper tool for each job, such as the correct roller, power sprayer, and the right size brush. Choosing the right tool typically depends on the surface to be covered and the characteristics of the finish.

A few painters--mainly industrial--must use special safety equipment. For example, painting in confined spaces such as the inside of a large storage tank, requires workers to wear self-contained suits to avoid inhaling toxic fumes. When painting bridges, tall buildings, or oil rigs, painters may work from scaffolding, bosun's chairs, and harnesses to reach work areas.

The following are examples of types of painters:  

Construction painters apply paints, stains, and coatings to interior and exterior walls, new buildings, and other structural surfaces.

Maintenance painters remove old finishes and apply paints, stains, and coatings later in a structure's life. Some painters specialize in painting or coating industrial structures, such as bridges and oil rigs, to prevent corrosion.

Artisan painters specialize in creating distinct finishes by using one of many decorative techniques. One technique is adding glaze for added depth and texture. Other common techniques may include sponging, distressing, rag-rolling, color blocking, and faux finishes. 

Painting and coating workers apply materials to manufactured products, such as furniture, toys and pottery, as well as transportation equipment including trucks, buses, boats, and airplanes. For more information about these painters, see the profile on painting and coating workers.


Hazardous Materials Removal Workers

Hazardous materials (hazmat) removal workers identify and dispose of asbestos, radioactive and nuclear waste, arsenic, lead, and other hazardous materials. They also clean up materials that are flammable, corrosive, reactive, or toxic.

Hazmat removal workers typically do the following:

  • Comply with safety procedures and federal laws regarding waste disposal
  • Construct scaffolding or build containment areas before cleaning up
  • Remove or clean up hazardous materials that are found or spilled
  • Clean contaminated equipment for reuse
  • Operate equipment that removes and stores waste materials
  • Keep records of cleanup activities

Hazmat removal workers clean up materials that are harmful to people and the environment. The work they do depends on the substances they are cleaning. Removing lead and asbestos is different from cleaning up radiation contamination and toxic spills. Differences also can relate to why these workers have been called in to clean a site. For example, cleaning up a fuel spill from a train derailment is more urgent than removing lead paint from a bridge.

The following are types of hazmat removal workers:

Asbestos abatement workers and lead abatement workers remove asbestos and lead from buildings that are going to be fixed up or taken down. Most of this work is in older buildings that were originally built with asbestos insulation and lead-based paints--both of which are now banned from being used in newer buildings and must be removed from older ones.

Until the 1970s, asbestos was often used in buildings for fireproofing, insulation, and other uses. However, asbestos particles can cause deadly lung diseases. Similarly, until the 1970s, lead was commonly used in paint, pipes, and plumbing fixtures. Inhaling lead dust or ingesting chips of lead-based paint can cause serious health problems, though, especially in children.

Lead abatement workers use chemicals and may need to know how to operate sandblasters, high-pressure water sprayers, and other common tools.

Decommissioning and decontamination workers remove and treat radioactive materials generated by nuclear facilities and powerplants. They break down contaminated items such as “gloveboxes,” which are used to process radioactive materials. When a facility is being closed or decommissioned (taken out of service), these workers clean the facility and decontaminate it from radioactive materials.

Decontamination technicians do tasks similar to those of janitors and cleaners, but the items and areas they clean are radioactive. Some of these jobs are now being done by robots controlled by people away from the contamination site. Increasingly, many of these remote devices automatically monitor and survey floors and walls for contamination.

Emergency and disaster response workers must work quickly to clean up hazardous materials after train and trucking accidents. Immediate, thorough cleanups help to control and prevent more damage to accident or disaster sites.

Radiation-protection technicians use radiation survey meters and other remote devices to locate and assess the hazard associated with radiated materials, operate high-pressure cleaning equipment for decontamination, and package radioactive materials for moving or disposing.

Treatment, storage, and disposal workers transport and prepare materials for treatment, storage, or disposal. To ensure proper treatment of materials, workers must follow laws enforced by the U.S. Environmental Protection Agency (EPA) or the U.S. Occupational Safety and Health Administration (OSHA). At incinerator facilities, treatment, storage, and disposal workers move materials from the customer or service center to the incinerator. At landfills, they organize and track the location of items in the landfill and may help change the state of a material from liquid to solid to prepare it to be stored. These workers typically operate heavy machinery, such as forklifts, earthmoving machinery, and large trucks and rigs.

Mold remediation makes up a small segment of hazardous materials removal work. Although mold is present in almost all structures and is not usually defined as a hazardous material, some mold--especially the types that cause allergic reactions--can infest a building to such a degree that extensive efforts must be taken to remove it safely.


Drywall and Ceiling Tile Installers, and Tapers

Drywall and ceiling tile installers hang wallboards to walls and ceilings inside buildings. Tapers prepare the wallboards for painting, using tape and other materials. Many workers do both installing and taping.

Drywall installers typically do the following:

  • Review design plans to minimize the number of cuts and waste of wallboard
  • Measure the location of electrical outlets, plumbing, windows, and vents
  • Cut drywall to the right size, using utility knives and power saws
  • Fasten drywall panels to interior wall studs, using nails or screws
  • Trim and smooth rough edges so boards join evenly

Ceiling tile installers typically do the following:

  • Measure according to blueprints or drawings
  • Nail or screw supports
  • Put tiles or sheets of shock-absorbing materials on ceilings  
  • Keep the tile in place with cement adhesive, nails, or screws

Tapers typically do the following:

  • Prepare wall surface (wallboard) by patching nail holes
  • Apply tape and use sealing compound to cover joints between wallboards
  • Apply additional coats of sealing compound to create an even surface
  • Sand all joints and holes to a smooth, seamless finish

Installers are also called framers or hangers. Tapers are also called finishers. Ceiling tile installers are sometimes called acoustical carpenters because they work with tiles that block sound.

Once wallboards are hung, workers use increasingly wider trowels to spread multiple coats of spackle over cracks, indentations, and any remaining imperfections. Some workers may use a mechanical applicator, a tool that spreads sealing compound on the wall joint while dispensing and setting tape at the same time.

To work on ceilings, drywall and ceiling tile installers and tapers may use mechanical lifts or stand on stilts, ladders, or scaffolds.


Janitors and Building Cleaners

Janitors and building cleaners keep many types of buildings clean, orderly, and in good condition.

Janitors and building cleaners typically do the following:

  • Gather and empty trash and trash bins
  • Clean building floors by sweeping, mopping, or vacuuming them
  • Clean bathrooms and stock them with soap, toilet paper, and other supplies
  • Keep buildings secure by locking doors
  • Clean spills and other hazards using sponges and squeegees
  • Wash windows, walls, and glass
  • Order cleaning supplies
  • Make minor repairs to the building, such as changing light bulbs
  • Notify managers when the building needs major repairs

Janitors and building cleaning workers keep office buildings, schools, hospitals, retail stores, hotels, and other places clean, sanitary, and in good condition. Some do only cleaning, while others have a wide range of duties.

In addition to keeping the inside of buildings clean and orderly, some janitors and building cleaners work outdoors, mowing lawns, sweeping walkways, or shoveling snow. Some janitors also monitor the heating and cooling system, ensuring that it functions properly.

Janitors and building cleaners use many tools and equipment. Simple cleaning tools may include mops, brooms, rakes, and shovels. Other tools may include snowblowers and floor buffers.

Some janitors may be responsible for repairing small problems with electricity or plumbing, such as leaky faucets.


Nationwide OversprayU.S. Forensic