Kanmar Construction

Carpet installers lay carpet in homes, offices, restaurants, and many other types of buildings. 

Carpet installers typically do the following:

• Remove old carpet or flooring to prepare surfaces for laying new carpet
• Inspect the condition of the surface to be covered
• Fix any problems that could show through the carpet or cause uneven wear
• Measure the area to be carpeted
• Plan the layout of carpeting to get the best appearance and least wear
• Install a padded cushion underneath the carpet
• Roll out, measure, mark, and cut the carpet
• Fit the carpet so that it lays evenly and snugly
• Tack, glue, or staple carpeting to hold it in place
• Finish the edges so that the carpet looks neat

Carpet installers lay carpet in many types of new and old buildings, including homes, offices, restaurants, and museums. Although installing carpet in newly constructed buildings requires minimal preparation, those who replace existing carpet must first remove old flooring, including any padding, glue, tacks, or staples. In some cases, carpet installers lay carpet over existing tile or hardwood.

Carpet installers work with special tools, including a "knee kicker" to position the carpet and a power stretcher to pull the carpet snugly against walls. When they have to join seams of carpet (for example, in large rooms), they use special heat-activated tape. In commercial installations, they may glue the carpet to the floor or to padding that they have glued to the floor. On steps, they may use staples to hold the carpet in place. They also use carpet knives, carpet shears (scissors), hammers, power sanders, and other tools.

Construction and building inspectors ensure that new construction, changes, or repairs comply with local and national building codes and ordinances, zoning regulations, and contract specifications.

Construction and building inspectors typically do the following:

• Review and approve plans that meet building codes, local ordinances, and zoning regulations
• Inspect and monitor construction sites to ensure overall compliance
• Use survey instruments, metering devices, and test equipment to perform inspections
• Monitor installation of plumbing, electrical, and other systems to ensure that the building meets codes
• Verify level, alignment, and elevation of structures and fixtures to ensure building compliance
• Issue violation notices and stop-work orders until building is compliant
• Keep daily logs, including photographs taken during inspection

Construction and building inspectors examine buildings, highways and streets, sewer and water systems, dams, bridges, and other structures. They also inspect electrical; heating, ventilation, air-conditioning, and refrigeration (HVACR); and plumbing systems. Although no two inspections are alike, inspectors do an initial check during the first phase of construction and follow-up inspections throughout the construction project. When the project is finished, they do a final, comprehensive inspection.

The following are types of construction and building inspectors:

Building inspectors check the structural quality and general safety of buildings. Some specialize in structural steel or reinforced-concrete structures, for example.

Electrical inspectors examine the installed electrical systems to ensure they function properly and comply with electrical codes and standards. The inspectors visit worksites to inspect new and existing sound and security systems, wiring, lighting, motors, and generating equipment. They also inspect the installed electrical wiring for HVACR systems and appliances.

Elevator inspectors examine lifting and conveying devices, such as elevators, escalators, moving sidewalks, lifts and hoists, inclined railways, ski lifts, and amusement rides.

Home inspectors typically inspect newly built or previously owned homes, condominiums, townhomes, and other dwellings. Prospective home buyers often hire home inspectors to check and report on a home's structure and overall condition. Sometimes, homeowners hire a home inspector to evaluate their home's condition before placing it on the market.

In addition to examining structural quality, home inspectors examine all home systems and features, including roofing, exterior walls, attached garage or carport, foundation, interior, plumbing, electrical, and HVACR systems. They look for and report violations of building codes, but they do not have the power to enforce compliance with the codes.

Mechanical inspectors examine the installation of HVACR systems and equipment to ensure that they are installed and function properly. They also may inspect commercial kitchen equipment, gas-fired appliances, and boilers.

Plan examiners determine whether the plans for a building or other structure comply with building codes. They also determine whether the structure is suited to the engineering and environmental demands of the building site.

Plumbing inspectors examine the installation of potable water, waste, and vent piping systems to ensure the safety and health of the drinking water system, piping for industrial uses, and the sanitary disposal of waste.

Public works inspectors ensure that federal, state, and local government water and sewer systems, highways, streets, bridges, and dam construction conform to detailed contract specifications. Workers inspect excavation and fill operations, the placement of forms for concrete, concrete mixing and pouring, asphalt paving, and grading operations. Public works inspectors may specialize in highways, structural steel, reinforced concrete, or ditches. Others specialize in dredging operations required for bridges and dams or for harbors.

Specification inspectors ensure that work is performed according to design specifications. Specification inspectors represent the owner's interests, not those of the general public. Insurance companies and financial institutions also may use their services.

A primary concern of building inspectors is fire prevention safety. For more information, see the profile on fire inspectors and investigators.

Tile and marble setters apply hard tile, marble, and wood tiles to walls, floors, and other surfaces.

Tile and marble setters typically do the following:

• Clean and level the surface to be tiled
• Measure and cut tile and marble
• Arrange tiles according to the design plans
• Prepare and apply mortar or other adhesives
• Install tile and marble in the planned area
• Apply grout with a rubber trowel
• Wipe off excess grout and apply necessary finishes, such as sealants

Tile installers, tilesetters, and marble setters install materials on a variety of surfaces, such as floors, walls, ceilings, countertops, patios, and roof decks. Because tile and marble must be set on smooth, even surfaces, installers often must level the surface to be tiled with a layer of mortar or plywood. If the area to be tiled is unstable, workers must nail a support of metal mesh or tile backer board to create a stable surface.

To cut tiles, workers use power wet saws, tile scribes, or hand-held tile cutters to create even edges. They use trowels of different sizes to spread mortar or a sticky paste, called mastic, evenly on the surface to be tiled. To minimize imperfections and keep rows straight and even, they put spacers between tiles. The spacers keep tiles the same distance from each other until the mortar is dry. After the mortar dries and the tiles are set, they apply grout between tiles using a rubber trowel (called a float).

Marble setters may cut marble to a specified size with a power wet saw. After putting the marble in place, marble setters polish the marble to a high luster, using power or hand sanders.

Metal and plastic machine workers set up and operate machines that cut, shape, and form metal and plastic materials or pieces.

Metal and plastic machine workers typically do the following:

• Set up machines and monitor them for unusual sound or vibration
• Lift material onto machines, manually or with a hoist
• Operate metal or plastic molding, casting, or coremaking machines
• Adjust the machines' speed and other settings
• Adjust cutting machine settings to account for irregularities
• Stop machines and remove finished products
• Test and measure finished products
• Remove and replace dull cutting tools
• Document production numbers in a computer database

Consumer products are made with many metal and plastic parts. These parts are produced by machines that are operated by metal and plastic machine workers. In general, these workers are separated into two groups: those who set up machines for operation and those who operate machines during production.

Although many workers both set up and operate the machines, some specialize in one of the following job types:

Machine setters, or setup workers, prepare the machines before production, perform test runs, and, if necessary, adjust and make minor repairs to the machinery before and during operation.

If, for example, the cutting tool inside a machine becomes dull after extended use, it is common for a setter to remove the tool, use a grinder or file to sharpen it, and place it back into the machine.

New tools are produced by tool and die makers. For more information, see the profile on machinists and tool and die makers.

After installing the tools into a machine, setup workers often produce the initial batch of goods, inspect the products, and turn the machine over to an operator.

Machine operators and tenders monitor the machinery during operation.

After a setter prepares a machine for production, an operator observes the machine and the products it produces. Operators may have to load the machine with materials for production or adjust the machine's speeds during production. They must periodically inspect the parts a machine produces. If they detect a minor problem, operators may fix it themselves. If the repair is more serious, they may have an industrial machinery mechanic fix it. For more information, see the profile on industrial machinery mechanics and maintenance workers. 

Setters, operators, and tenders usually are identified by the type of machine they work with. Job duties usually vary with the size of the manufacturer and the type of machine being operated. Although some workers specialize in one or two types of machinery, many are trained to set up or operate a variety of machines. Increasing automation allows machine setters to operate multiple machines at the same time.

In addition, newer production techniques, such as team-oriented “lean” manufacturing, require machine operators to rotate between different machines. Rotating assignments results in more varied work but also requires workers to have a wider range of skills.

The following are types of metal and plastic machine workers:

Computer-controlled machine tool operators, metal and plastic operate computer-controlled machines or robots to perform functions on metal or plastic workpieces.

Computer numerically controlled machine tool programmers, metal and plastic develop programs to control the machining or processing of metal or plastic parts by automatic machine tools, equipment, or systems.                                               

Extruding and drawing machine setters, operators, and tenders, metal and plastic set up or operate machines to extrude (pull out) or draw thermoplastic or metal materials into tubes, rods, hoses, wire, bars, or structural shapes. 

Forging machine setters, operators, and tenders, metal and plastic set up or operate machines that taper, shape, or form metal or plastic parts.

Rolling machine setters, operators, and tenders, metal and plastic set up or operate machines to roll steel or plastic or to flatten, temper, or reduce the thickness of material.

Cutting, punching, and press machine setters, operators, and tenders, metal and plastic set up or operate machines to saw, cut, shear, notch, bend, or straighten metal or plastic material.

Drilling and boring machine tool setters, operators, and tenders, metal and plastic set up or operate drilling machines to drill, bore, mill, or countersink metal or plastic workpieces.

Grinding, lapping, polishing, and buffing machine tool setters, operators, and tenders, metal and plastic set up or operate grinding and related tools that remove excess material from surfaces, sharpen edges or corners, or buff or polish metal or plastic workpieces.

Lathe and turning machine tool setters, operators, and tenders, metal and plastic set up or operate lathe and turning machines to turn, bore, thread, form, or face metal or plastic materials, such as wire or rod.

Milling and planing machine setters, operators, and tenders, metal and plastic set up or operate milling or planing machines to shape, groove, or profile metal or plastic workpieces.

Metal-refining furnace operators and tenders operate or tend furnaces, such as gas, oil, coal, electric-arc or electric induction, open-hearth or oxygen furnaces to melt and refine metal before casting or to produce specified types of steel.

Pourers and casters, metal operate hand-controlled mechanisms to pour and regulate the flow of molten metal into molds to produce castings or ingots.

Model makers, metal and plastic set up and operate machines, such as milling and engraving machines and jig borers, to make working models of metal or plastic objects.

Patternmakers, metal and plastic lay out, machine, fit, and assemble castings and parts to metal or plastic foundry patterns, coreboxes, or match plates.

Foundry mold and coremakers make or form wax or sand cores or molds used in the production of metal castings in foundries.

Molding, coremaking, and casting machine setters, operators, and tenders, metal and plastic set up or operate metal or plastic molding, casting, or coremaking machines to mold or cast metal or thermoplastic parts or products.

Multiple machine tool setters, operators, and tenders, metal and plastic set up or operate more than one type of cutting or forming machine tool or robot.

Welding, soldering, and brazing machine setters, operators, and tenders (including workers who operate laser cutters or laser-beam machines) set up or operate welding, soldering, or brazing machines or robots that weld, braze, solder, or heat treat metal products, components, or assemblies.

Heat treating equipment setters, operators, and tenders, metal and plastic set up or operate heating equipment, such as heat treating furnaces, flame-hardening machines, induction machines, soaking pits, or vacuum equipment, to temper, harden, anneal, or heat treat metal or plastic objects.

Plating and coating machine setters, operators, and tenders, metal and plastic set up or operate plating or coating machines to coat metal or plastic products with zinc, copper, nickel, or some other metal to protect or decorate surfaces (includes electrolytic processes).

Construction equipment operators drive, maneuver, or control the heavy machinery used to construct roads, bridges, buildings, and other structures.

Construction equipment operators typically do the following:

• Check to make sure that equipment functions properly
• Clean, maintain, and make basic repairs to equipment
• Report malfunctions to supervisors
• Move levers, push pedals, or turn valves to activate power equipment
• Drive and maneuver equipment
• Coordinate machine actions with crew members in response to hand or audio signals
• Ensure that safety standards are met

Construction equipment operators use machinery to move construction materials, earth, and other heavy materials at construction sites and mines. They operate equipment that clears and grades land to prepare it for construction of roads, bridges, and buildings, as well as airport runways, power generation facilities, dams, levees, and other structures.

The following are types of construction equipment operators:

Operating engineers and other construction equipment operators work with one or several types of power construction equipment. They may operate excavation and loading machines equipped with scoops, shovels, or buckets that dig sand, gravel, earth, or similar materials. In addition to operating the familiar bulldozer, they operate trench excavators, road graders, and similar equipment. Sometimes, they may drive and control industrial trucks or tractors equipped with forklifts or booms for lifting materials. They also may operate and maintain air compressors, pumps, and other power equipment at construction sites.

Paving and surfacing equipment operators control the machines that spread and level asphalt or spread and smooth concrete for roadways or other structures. Paving and surfacing equipment operators may specialize further:

• Asphalt spreader operators turn valves to regulate the temperature of asphalt and the flow of asphalt onto the roadbed. They must ensure that the machine distributes the paving material evenly, and they also must ensure that there is a constant flow of asphalt into the hopper.
• Concrete paving machine operators control levers and turn handwheels to move attachments that spread, vibrate, and level wet concrete. They must watch the surface of the concrete carefully to identify low spots into which workers must add concrete.
• Tamping equipment operators use machines that compact earth and other fill materials for roadbeds or other construction sites. They also may operate machines with interchangeable hammers to cut or break up old pavement and drive guardrail posts into the ground.

Piledriver operators use large machines mounted on skids, barges, or cranes to hammer piles into the ground. Piles are long, heavy beams of wood or steel driven into the ground to support retaining walls, bridges, piers, or building foundations. Some piledriver operators work on offshore oil rigs.

Some workers operate cranes to move construction materials. For more information on these workers, see the profile on material moving machine operators.